Delphi 28231014 Diesel Injector
2.0L Diesel · 28231014
Great Wall 2.0 Diesel (GW4D20) Delphi remanufactured common-rail injector
1
Engine codes
4
OE / cross-refs
4
Vehicle fitments
12mo
Warranty
Common failure symptoms
On the 2.0L Diesel platform, a failing Delphi 28231014 injector typically presents as: hard starting or extended cranking; rough or uneven idle; loss of power under load; excess smoke from the exhaust; cylinder misfire or contribution fault codes.
When two or more of these appear together, suspect the injector before peripheral systems — a comparative leak-off test and live-data cylinder-balance review will isolate the failed unit without tear-down.
When two or more symptoms appear together, suspect the injector before peripherals (EGR, glow plugs, turbo). A live-data leak-off test on each cylinder is the fastest route to the failed unit.
What Causes These Injectors To Fail
The documented failure modes on this platform are: injector back-leak beyond specification; nozzle wear degrading the spray pattern; combustion gas leaks past the injector seat washer.
Internal wear cannot be repaired in situ — once delivery drifts outside calibration, remanufacture or replacement is the reliable fix.
How Workshops Diagnose 28231014 Faults
Run a comparative leak-off (back-leak) test across all injectors before condemning a single unit. Compare requested vs actual rail pressure in live data at idle and under load. Inspect injector connectors and wiring before replacing hardware.
Never condemn a common-rail injector on a fault code alone — codes identify the circuit or cylinder, while leak-off volumes and correction values identify the component.
How Every Unit Is Tested Before Despatch
Each remanufactured 28231014 is fully stripped, ultrasonically cleaned and inspected; worn components are replaced with OE-grade parts. The rebuilt unit is then calibrated on a common-rail test bench against the manufacturer's specification sheet — delivery, back-leak and response are all verified before the injector is sealed and despatched with its calibration data on file.
Every unit carries a 12-month parts warranty and free UK delivery.
Vehicle Coverage At A Glance
The 28231014 trusted family covers 4 verified vehicle fitments across 1 make: Great Wall. Every fitment listed on this page is registry-verified — no scraped or assumed applications.
OE & Cross-References
28231014 supersedes or cross-references 3 further OE numbers, including HRD367, 1100100-ED01 and 1100100ED01. Always match the reference etched on your failed unit's body — cross-references within a family are verified equivalents, but etched numbers remain the source of truth.
Related fault codes & engine guides
Engine guides
Trusted compatibility
Engine codes
OE / cross-references (3)
Vehicle fitments
| Make | Model | Engine | Years |
|---|---|---|---|
| Great Wall | Cowry (V80) | 2.0 Diesel (GW4D20) | 2011–2014 |
| Great Wall | Hover | 2.0 Diesel (GW4D20) | 2011–2015 |
| Great Wall | Haval H5 | 2.0 Diesel (GW4D20) | 2011–2015 |
| Great Wall | Wingle (Steed) | 2.0 Diesel (GW4D20) | 2011–2018 |
Confirm fitment by registration
Enter your UK registration to verify your vehicle is in this trusted family. We'll cross-check the engine code against 4D20.
Confirm fitment for your vehicle
Frequently asked
Related engine guides
Other Delphi and same-platform injector families worth checking.
All cross-references in this family
Every reference below resolves to a PDP linked to this trusted family. 28231014, HRD367, 1100100-ED01, 1100100ED01.
Delphi know-how from the Knowledge Centre
Identification, coding, fitting and the mistakes that cause comebacks.