DCRI105600 — Technical Research
Denso solenoid common-rail injector for the Mitsubishi 3.2 DI-D (4M41) engine, fitted to Pajero/Shogun, L200 and Canter. Denso factory numbers 095000-560x; Mitsubishi 1465A041. Failures are driven by poor fuel filtration, contamination and back-leakage; a replacement is coded to the ECU with the Denso QR/ID code. Key symptoms: Rough idle / vibration; Hard starting; Loss of power / limp mode; Black smoke. Common failure modes: Internal wear / high back-leakage; Water-in-fuel corrosion; Nozzle coking.
Denso DCRI105600 3.2 DI-D (4M41) Common Rail Injector (Mitsubishi Pajero/Shogun/L200)
Denso solenoid common-rail injector for the Mitsubishi 3.2 DI-D (4M41) engine, fitted to Pajero/Shogun, L200 and Canter. Denso factory numbers 095000-560x; Mitsubishi 1465A041. Failures are driven by poor fuel filtration, contamination and back-leakage; a replacement is coded to the ECU with the Denso QR/ID code. Key symptoms: Rough idle / vibration; Hard starting; Loss of power / limp mode; Black smoke. Common failure modes: Internal wear / high back-leakage; Water-in-fuel corrosion; Nozzle coking.
A leaking injector unbalances cylinder fuelling on the 4M41.
Excess back-leakage drops cranking rail pressure.
Out-of-range delivery or rail-pressure deviation cuts power.
Poor atomisation over-fuels the cylinder.
Cylinder-specific injector or fuel-metering codes.
- InstallationWrite the Denso injector ID/QR correction code to the correct cylinder with Mitsubishi MUT-III before road test.
- InstallationRenew the combustion seal and clamp hardware and torque to spec.
- MisdiagnosisRead live correction/back-leakage data to find the weak cylinder before removal.
- WarningFix contamination (filter/water/debris) first to protect the new injector.
- TestingBench-test across delivery and back-leakage points; verify spray pattern.
What is Denso injector DCRI105600?+
A Denso solenoid common-rail diesel injector for the Mitsubishi 3.2 DI-D (4M41) engine. Denso factory numbers 095000-560x; Mitsubishi 1465A041.
Which vehicles use DCRI105600?+
Mitsubishi Pajero, Shogun, L200 and Canter 3.2 DI-D (4M41).
Is it solenoid or piezo?+
It is a Denso solenoid common-rail injector.
What are the OE part numbers?+
Mitsubishi 1465A041 and the Denso 095000-5600 series reference DCRI105600.
Does it need coding?+
Yes - write the Denso ID/QR correction code to the correct cylinder with Mitsubishi MUT-III when fitting.
What are the symptoms of failure?+
Rough idle, vibration, hard starting, black smoke, power loss/limp mode and an EML.
Why does my Shogun 3.2 DI-D run rough?+
A worn or leaking injector unbalances fuelling; read live correction data and bench-test the cylinder.
What causes these injectors to fail?+
Poor fuel filtration, contamination and back-leakage wear - fix the cause first.
Do I need to renew the seals?+
Yes - renew the combustion seal and clamp hardware; reused seals cause blow-by.
Does a remanufactured DCRI105600 perform like new?+
A properly remanufactured injector is bench-tested and recalibrated to the Denso plan, then ID-coded on fitment.