Skip to main content

Ships Worldwide•FREE UK•£50 International

Trade customer? Get Trade Pricing
OEM Tested
12-Month Warranty
Free UK Delivery
Same-Day Dispatch

UFDA Diesel Injectors

Compatible with Ford Kuga, Peugeot 607

  • OEM Tested & Calibrated
  • 12-Month Warranty
  • Free UK Delivery

Select the correct injector for your UFDA engine below

Fits Ford Kuga, Peugeot 607 and more

Compatible Injectors for UFDA

  • OEM Tested
  • 12-Month Warranty
  • Free UK Delivery
Check CompatibilityCall 020 3355 6581
Order by 2pm — tracked UK courier

Common problems solved by these injectors

About the UFDA engine

The UFDA is a dw10 / 2.0 hdi / 2.0 tdci / d4204t common rail diesel engine. This engine uses Siemens VDO / Continental diesel injectors.

How Diesel Injectors Are Remanufactured

Watch our 3D walkthrough of the diesel injector remanufacturing process and see how injectors are professionally restored for reliable service.

Vehicles Using UFDA Engine

VehicleEngineYears
Ford Kuga injector 2.0 TDCi2008-2012
Peugeot 607 injector 2.0 HDi2004–2010

Common UFDA Injector Problems

1

Rough idle and engine vibration

Worn injector nozzles cause uneven fuel spray, leading to rough idle at low RPM. Most noticeable when the engine is cold.

2

Excessive exhaust smoke

Black or blue-grey smoke on acceleration indicates poor fuel atomisation. This is often caused by carbon buildup on the injector nozzle tip.

3

Poor fuel economy

A worn or leaking injector delivers incorrect fuel quantities, reducing efficiency by 10–20% in severe cases.

4

Engine misfire under load

Intermittent misfires during acceleration suggest one or more injectors are failing to deliver the correct fuel pressure.

5

Difficult cold starting

Degraded injector nozzles struggle to atomise fuel at lower cranking pressures, causing extended crank times in cold weather.

6

Loss of power

Gradual power loss across the rev range, particularly above 2500 RPM, can indicate injector flow rate degradation.

7

Increased diesel knock

Louder than normal combustion noise, especially at idle, can indicate incorrect injection timing due to worn injector internals.

UFDA Technical Specifications

Displacement

—

Power

—

Torque

—

Fuel System

Common Rail Direct Injection

The UFDA is a dw10 / 2.0 hdi / 2.0 tdci / d4204t common rail diesel engine. This engine uses Siemens VDO / Continental diesel injectors.

Engine Intelligence

PSA / Ford / Volvo 2.0 HDi / TDCi / D (DW10 — Siemens piezo)

Documented failure modes

  • Piezo injector internal leak-back rising with temperature
  • Rail pressure failing to build during hot cranking
  • Injector back-leak overwhelming high-pressure pump delivery
  • Wiring/connector chafing causing injector circuit faults

Diagnostic guidance

  • Measure injector back-leak (leak-off) both cold and fully warm before condemning — this family's leak-back typically worsens with temperature
  • Compare requested vs actual rail pressure during cranking in live data
  • Piezo injectors must never be energised with solenoid-type test currents
  • Fit new sealing washers and follow the manufacturer classification/coding procedure after replacement

Fault codes linked to this engine's injectors

Fitment note: This Siemens/Continental piezo family spans PSA (RHR/RHF…), Ford (QXBA/UFBA…) and Volvo (D4204T) builds of the same 2.0 engine — always confirm the part number etched on the injector body before ordering.

Browse every diesel engine we cover →

Related UFDA Engine Guides

Related Pages

Siemens VDO / Continental DW10 / 2.0 HDi / 2.0 TDCi / D4204T — browse compatible engines, vehicles, and injectors

More resources for UFDA owners