IXDA Diesel Injectors
Compatible with Ford C-Max, Ford Focus
- OEM Tested & Calibrated
- 12-Month Warranty
- Free UK Delivery
Select the correct injector for your IXDA engine below
Fits Ford C-Max, Ford Focus and more
Top injectors for IXDA
Compatible Injectors for IXDA
- OEM Tested
- 12-Month Warranty
- Free UK Delivery
Common problems solved by these injectors
About the IXDA engine
The IXDA is a dw10 / 2.0 hdi / 2.0 tdci / d4204t common rail diesel engine. This engine uses Siemens VDO / Continental diesel injectors.
How Diesel Injectors Are Remanufactured
Watch our 3D walkthrough of the diesel injector remanufacturing process and see how injectors are professionally restored for reliable service.
Vehicles Using IXDA Engine
| Vehicle | Engine | Years |
|---|---|---|
| Ford C-Max injector | 2.0 TDCi | 2007-2010 |
| Ford Focus injector | 2.0 TDCi | 2003-2012 |
Common IXDA Injector Problems
Rough idle and engine vibration
Worn injector nozzles cause uneven fuel spray, leading to rough idle at low RPM. Most noticeable when the engine is cold.
Excessive exhaust smoke
Black or blue-grey smoke on acceleration indicates poor fuel atomisation. This is often caused by carbon buildup on the injector nozzle tip.
Poor fuel economy
A worn or leaking injector delivers incorrect fuel quantities, reducing efficiency by 10–20% in severe cases.
Engine misfire under load
Intermittent misfires during acceleration suggest one or more injectors are failing to deliver the correct fuel pressure.
Difficult cold starting
Degraded injector nozzles struggle to atomise fuel at lower cranking pressures, causing extended crank times in cold weather.
Loss of power
Gradual power loss across the rev range, particularly above 2500 RPM, can indicate injector flow rate degradation.
Increased diesel knock
Louder than normal combustion noise, especially at idle, can indicate incorrect injection timing due to worn injector internals.
IXDA Technical Specifications
Displacement
—
Power
—
Torque
—
Fuel System
Common Rail Direct Injection
The IXDA is a dw10 / 2.0 hdi / 2.0 tdci / d4204t common rail diesel engine. This engine uses Siemens VDO / Continental diesel injectors.
Engine Intelligence
PSA / Ford / Volvo 2.0 HDi / TDCi / D (DW10 — Siemens piezo)
Documented failure modes
- Piezo injector internal leak-back rising with temperature
- Rail pressure failing to build during hot cranking
- Injector back-leak overwhelming high-pressure pump delivery
- Wiring/connector chafing causing injector circuit faults
Diagnostic guidance
- Measure injector back-leak (leak-off) both cold and fully warm before condemning — this family's leak-back typically worsens with temperature
- Compare requested vs actual rail pressure during cranking in live data
- Piezo injectors must never be energised with solenoid-type test currents
- Fit new sealing washers and follow the manufacturer classification/coding procedure after replacement
Fitment note: This Siemens/Continental piezo family spans PSA (RHR/RHF…), Ford (QXBA/UFBA…) and Volvo (D4204T) builds of the same 2.0 engine — always confirm the part number etched on the injector body before ordering.
Related IXDA Engine Guides
Related Pages
Siemens VDO / Continental DW10 / 2.0 HDi / 2.0 TDCi / D4204T — browse compatible engines, vehicles, and injectors
Compatible Engines
Compatible Vehicles
Recommended Injector
5WS40156-Z
Siemens VDO / Continental — View product page
